Microsoft reserves the right to modify or discontinue offers at any time to the extent permitted by applicable law. Promotional items given, or discounted products bought with, a qualifying product are not valid or must be returned if the qualifying product is returned. Applicable return policy applies to each purchase. Not valid on prior orders or purchases cannot be transferred or otherwise redeemed for cash or promo code(s). Offer valid only on select Earbuds, after purchase of select Huawei MateBook X Pro. Available only in Microsoft Store online in Australia. Offer valid from 12AM on 6 January 2022 to 11:59PM on 31 December 2022, while supplies last. Maximum battery capacity decreases with time and use. **Battery life varies by configuration, operating conditions and other factors. The youth size helmet is recommended for riders 8 -14 years old, but will fit anyone with a head measuring 54 - 58 cm. Certain features require specific hardware, see. Swipe the sequin center panel of the bicycle helmet to change the sequin color from purple to silver and back again The fabric side panels of the helmet are printed with a cute feather pattern. * AC load in Low Energy (standby) mode: less than 1VAįor additional information, please check the "Documentation" tab.*Upgrade rollout plan is being finalized and is scheduled to begin late in 2021 and continue into 2022. * AC load: 1,350VA or less with a power factor of 0.95 or higher AOM-700S has NO PLUG order this model to wire your own AC plug for either voltage. AOM-700S-120 is pre-wired with NEMA 5-15P for 120 volt operation. AOM-700S-240 is pre-wired with NEMA 6-15P USA plug for 240 volt operation. SPECIAL NOTE: Due to power efficiency the use of 240 Vac service is highly recommended. **Mains supply voltage: 100-240V, 50-60 Hz, single phase, automatic switching supply no internal change required for either mains voltage European style 5x20mm fuses rated for 250VAC for correspond mains: 10A fuses for operation from 200-240VAC, 16À fuses for operation from 100-120VAC. * Relative humidity: up to 95 percent at 95 F (35 C) * Temperature range: 14 degrees F to 104 F (-10 C to +40 C) * Complies with US Federal Communications Commission (FCC) rules and the EU safety regulations and electromagnetic compatibility standards * Input circuit: broadband, SWR below 1.2:1, 1.8 to 54 MHz continuous without retuning or switching * Input and output impedances: SO-239 UHF female connectors 50 ohm unbalanced output * Harmonic and parasitic emissions suppression: Better than 60dB (65dB typical) * Intermodulation distortion (IMD3): Better than 31dB below rated PEP output These outstanding amplifiers are available from DX Engineering!ĪCOM 700S Solid State Linear Amplifier Specifications:
![stereo tools 8.54 stereo tools 8.54](https://www.mazterize.com/wp-content/uploads/2016/06/Thimeo-Stereo-Tool-min.jpg)
Please read the SPECIAL NOTE at the end of the specifications.ĪCOM 700S Solid State HF/6-Meter Amplifiers are among the finest and most modern linear amplifiers available anywhere in the world. They operate on an extended mains voltage range** (100-120VAC and 200-240VAC) by changing only the main fuses - no internal switching is required. They are extremely compact and employ light-weight construction thanks to the built-in switching-mode power supply. Detailed data (55 parameters) about each of the last 28 hard-fault protection trips is stored in the amplifier's nonvolatile memory.ĪCOM 700S amplifiers are perfect for DXpeditions and field operation. The operator can digitally monitor more than 10 parameters concerning the working conditions of the amplifier. These amplifiers take care of themselves during operation, due to the continuously-working protection circuits in all modes. A band data or CAT interface connection from the transceiver is NOT required for automatic band changing. The amplifier monitors the frequency of the input signal through the built-in frequency counter and automatically switches bands. Screen menus are intuitive and easy to follow and no special skill is required from the operator when changing frequency bands. The overall operation of ACOM 700S amplifiers is extremely simplified. The broadband input matches to the transceiver with low SWR over the entire range of 1.8-54 MHz.įull output operation only requires a maximum of 40 watts drive and the typical "ground on transmit" (PTT) keying with no special signals required.
![stereo tools 8.54 stereo tools 8.54](https://m.media-amazon.com/images/I/41zGVMIKe1L._AC_SL1000_.jpg)
Amplifier control is accomplished with only six buttons on the front panel or directly by CAT interface from the transceiver or remotely by RS232 interface.ĪCOM 700S amplifiers are compatible with all transceiver models available on the market. Working parameters of the amplifier are indicated on a multi-function, high-resolution 5 inch color display. These amps provide 700 W output power (PEP SSB or CW modes).
![stereo tools 8.54 stereo tools 8.54](https://ae01.alicdn.com/kf/H3e7c740be7114d93a2bddd83959e3198q.jpg)
Stereo tools 8.54 full#
line current 6A 240 Vac or 12A 120 Vac at full RF outputĪCOM 700S Solid State 1.8-54 MHz Linear AmplifiersĪCOM 700S Solid State 1.8-54 MHz Linear Amplifiers are state-of-the art amplifiers that cover all amateur bands from 160 through 6 Meters.